文献速递瓣膜外科

二尖瓣建模与三维打印用于二尖瓣修复的规划与模拟

Mitral valve modelling and three-dimensional printing for planning and simulation of mitral valve repair.
PubMed 文献 · Eur J Cardiothorac Surg · 2019-01-01

本研究基于三维经食管超声心动图(TOE)开发了病变二尖瓣的建模与三维打印流程,对10例不同二尖瓣疾病患者分别制作刚性塑料模型用于手术规划、硅胶铸型用于手术模拟,所有模型按比例制作并经术中评估验证,作者认为该流程可行,未来或可用于增强解剖判读、辅助复杂手术规划与模拟及培训。

要点

  • 基于三维经食管超声心动图可重建病变二尖瓣并打印按比例模型。
  • 6例制作刚性塑料模型用于手术规划,4例制作硅胶铸型用于手术模拟。
  • 刚性塑料模型制作耗时3至4小时、费用15至40欧元,硅胶模型耗时2至3天、费用300欧元。

核心结论

  • 作者证明制作刚性塑料与仿组织硅胶二尖瓣复制模型具有可行性。
  • 作者认为这些模型未来或可用于增强外科解剖判读、促进复杂手术的规划与模拟以及用于培训目的。

研究设计与样本

  • 本研究为基于三维经食管超声心动图(TOE)的二尖瓣建模与三维打印流程开发研究,对10例不同二尖瓣疾病的前瞻性患者进行建模。
  • 重建在瓣膜水平裁剪并于收缩中期截取以评估对合缺损,网格经计算机建模程序处理后打印。
  • 模拟用模型基于阴性模具制作并以仿组织硅胶浇铸,模型验证通过术中评估瓣膜病变与修复策略完成。

主要发现

  • 共对10例不同二尖瓣疾病患者的二尖瓣进行建模。
  • 6例制作三维打印刚性塑料二尖瓣用于手术规划,4例制作硅胶铸型复制品用于手术模拟。
  • 所有模型均按比例制作,保持体内尺寸,并经体内比较验证。
  • 刚性塑料模型总制作时间3至4小时、费用15至40欧元;硅胶模型总制作时间2至3天、费用300欧元。

局限性

  • 作者在结论中提出这些模型未来或可用于增强解剖判读、辅助复杂手术规划与模拟及培训,属于可行性层面的表述。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: The aim of this study was to develop a process for modelling and 3-dimensional (3D) printing of different mitral valve diseases for procedural planning and simulation, based on 3D transoesophageal echocardiography (TOE). METHODS: 3D TOE was used to reconstruct a fully dynamic 3D view of the diseased valve. Reconstructions were cropped at the level of the valve and captured in mid-systole to assess the coaptation defect. Reconstructions were then exported as a surface mesh. To ensure a watertight and noise-reduced model, the mesh was processed using computer-modelling programmes, whereupon the valve was printed in 3D. For simulation purposes, deformable models were created based on negative mould fabrication and cast in tissue-mimicking silicone. Model validation was performed by intraoperative assessment of the valvular disease and repair strategy. RESULTS: The mitral valves of 10 prospective patients with different diseases were modelled. In 6 patients, a 3D printed rigid plastic mitral valve was created for procedural planning, and in 4 patients, a silicone-cast replica was created for procedural simulation. All models were created to scale, implying conservation of in vivo dimensions. Models were validated by in vivo comparison. Total workaround time ranged from 3 to 4 h and 2 to 3 days for rigid plastic and silicone models, respectively. Costs were €15 to €40 and €300, respectively. CONCLUSIONS: We demonstrated the feasibility of creating rigid plastic and tissue-mimicking silicone mitral valve replications. These models could be used in the future to enhance surgical anatomical interpretation, to facilitate planning and simulation of complex surgeries and for training purposes.

来源:Eur J Cardiothorac Surg,查看原文。版权归原作者所有。

引用

  1. Daemen JHT, Heuts S, Olsthoorn JR, et al. Mitral valve modelling and three-dimensional printing for planning and simulation of mitral valve repair. Eur J Cardiothorac Surg. 2019. PMID: 30202862. doi:10.1093/ejcts/ezy306

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。