文献速递先天性心脏病外科

肺动脉ePTFE带瓣管道血流动力学的体外评估

In Vitro Hydrodynamic Evaluation of Pulmonary Expanded Polytetrafluoroethylene Valved Conduits.
PubMed 文献 · Interdiscip Cardiovasc Thorac Surg · 2026-01-01

本研究利用循环模拟器对三种24 mm基底环的肺动脉ePTFE带瓣管道模型(直筒型、小窦型、大窦型)进行体外血流动力学测试,评估其瓣膜行为和流体力学特征。结果显示各模型均有足够的开口面积和可接受的雷诺剪切应力,窦部结构有助于抑制湍流,且效果取决于窦部大小。

要点

  • 三种ePTFE管道模型均表现出足够的开口和可接受的雷诺剪切应力。
  • 窦部结构有助于抑制湍流,可能改善管道耐久性,但效果取决于窦部大小。
  • 大窦模型(C)的湍流分布趋势最低。

核心结论

  • 所有模型均表现出足够的开口和可接受的雷诺剪切应力值。
  • 窦部有助于抑制湍流,可能改善管道耐久性,但其效果取决于窦部大小。

研究设计与样本

  • 采用循环模拟器进行体外实验,评估三种24 mm基底环的3D打印根部模型(A直筒型、B小窦型、C大窦型)的血液动力学性能。
  • 瓣叶由0.1 mm厚ePTFE膜均匀裁剪并缝合至模型内壁,模型A在靠近 commissures 的自由缘处有单缝合。
  • 测试条件为泵容量70 mL、70次/分、动脉压30/10 mmHg,采用高速相机记录瓣膜行为并在模型 housing 段后方区域进行粒子图像测速(PIV)。

主要发现

  • 模型A、B、C的峰值跨瓣压力梯度分别为4.0、4.8、4.3 mmHg(P = .95)。
  • 模型A、B、C的几何开口面积分别为2.34、2.38、2.46 cm2(P = .96)。
  • PIV显示模型A、B、C的峰值瞬时速度分别为1.69、1.69、1.65 m/s(P = .74)。
  • 模型A、B、C在收缩中期的峰值雷诺剪切应力分别为56.8、49.5、25.5 Pa(P = .05)。
  • 模型C的湍流分布趋势低于其他模型。

临床怎么用

  • 体外实验提示窦部设计可能有助于抑制湍流,但窦部大小对效果有影响,临床选用ePTFE带瓣管道时可考虑窦部结构设计。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: Various designs are proposed for pulmonary expanded polytetrafluoroethylene (ePTFE) conduits and have been applied in clinical practice. However, experimental data to support them are limited. We conducted an in vitro experiment using a circulatory simulator to evaluate their haemodynamic performance and hydrodynamic characteristics. METHODS: Three root models with a 24-mm basal ring (A, straight; B, with small sinuses; C, with large sinuses) were 3D-printed. Cusps were uniformly cut out from a 0.1-mm-thick ePTFE membrane and sewn to the inter wall of the models. Model A had a single suture on the free margins near the commissures. Each model was tested with a pump size of 70 mL, 70 beats/min, and arterial pressure of 30/10 mmHg. The valve behaviour was recorded by a high-speed camera, and particle image velocimetry (PIV) was performed in the region behind the model housing section. RESULTS: Peak transvalvular pressure gradients were 4.0, 4.8, and 4.3 mmHg (P = .95), and geometric orifice areas were 2.34, 2.38, and 2.46 cm2 (P = .96) in models A, B, and C, respectively. Particle image velocimetry revealed peak instantaneous velocity was 1.69, 1.69, and 1.65 m/s (P = .74) and peak Reynolds shear stress in the midsystolic phase was 56.8, 49.5, and 25.5 Pa (P = .05) in models A, B, and C, respectively. Model C tended to have a lower distribution of turbulent flow than the other models. CONCLUSIONS: All models exhibited sufficient opening and acceptable Reynolds shear stress values. The sinus contributed to the suppression of turbulent flow, which may lead to an improvement of conduit durability, but its effect was dependent on the sinus size.

来源:Interdiscip Cardiovasc Thorac Surg,查看原文。版权归原作者所有。

引用

  1. Matsushima S, Noda M, Kubo S, et al. In Vitro Hydrodynamic Evaluation of Pulmonary Expanded Polytetrafluoroethylene Valved Conduits. Interdiscip Cardiovasc Thorac Surg. 2026. PMID: 41769822. doi:10.1093/icvts/ivag072

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。