实验性左心室辅助装置附件的压力分布与流场计算流体力学分析
该研究用计算流体力学模拟实验性左心室辅助装置附件内的压力与流速,在转速4000、5200、6400 rpm和流量1、5、8.4 L/min下计算泵进出口压差,并与通用装置模拟比较。结果显示转速升高使恒流下压头增加,流量5至8.4 L/min间压头下降大于1至5 L/min间,流出道弯曲度和分叉是下游压力损失主因。
要点
- 流出道弯曲强度与分叉是附件下游压力损失的主要来源。
- 转速升高时恒流下压头增加,符合自然泵特性。
- 下一代附件应减少弯曲并避免流出道分叉。
核心结论
- 实验性左心室辅助装置附件的压力损失主要源于流出道的弯曲和分叉。
- 下一代附件设计应聚焦于最小化弯曲并避免流出道分叉。
研究设计与样本
- 基于附件几何构建计算流体力学模型,模拟名义血流并量化压力与流速。
- 在转速4000、5200、6400 rpm和泵流量1、5、8.4 L/min下计算泵进出口压差。
- 结果与通用左心室辅助装置模拟比较以确定附件影响。
主要发现
- 转速升高导致恒流下压头增加,呈现自然泵特性。
- 所有案例中流量5至8.4 L/min间的压头下降大于1至5 L/min间。
- 流出道弯曲强度和通道分叉是下游压力损失的主要贡献因素。
临床怎么用
- 附件迭代设计应优先减少流出道弯曲并避免分叉以降低压力损失。
- 进一步开发可能实现仅经左胸切口植入且泵性能改变可忽略。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVES: Implantation of left ventricular assist devices conventionally requires a sternotomy and cardiopulmonary bypass. An experimental accessory was designed to redirect the device's outflow graft through the left ventricle into the ascending aorta. This design allows for implantation via left thoracotomy only but resulted in significant pressure loss both in vitro and in vivo. We evaluated the reasons for the pressure loss of the experimental accessory by quantifying pressure distribution and flow profiles using computational fluid dynamics simulation tools. METHODS: A computational fluid dynamics model based on the accessory's geometry was used to simulate nominal blood flow through the model. Quantities of interest included pressure and flow velocity. Pressure differences between the pump inlet and outlet were calculated at different rotational speeds (4000, 5200, 6400 rpm) and pump flow rates (1, 5, 8.4 L/min). Results were compared with simulations of a generic left ventricular assist device to determine the accessory's impact. RESULTS: Natural pump characteristics were observed, as increased rotational speed caused an increase in pressure head with a constant flow rate. For all cases, a greater decrease in pressure head was seen between 5 and 8.4 L/min than between 1 and 5 L/min. Curvature intensity and channel bifurcation in the outflow were the main contributors to downstream pressure loss. CONCLUSIONS: The next iteration of the left ventricular assist device accessory should focus on minimizing curvatures and avoiding bifurcations in the outflow. Further development may allow for less invasive left ventricular assist device implantation with negligible alterations in pump performance.
引用
- Osypka A, Meissner F, Ozturk D, et al. In silico analysis of pressure distribution and flow profiles across an experimental left ventricular assist device accessory. Interdiscip Cardiovasc Thorac Surg. 2025. PMID: 39999016. doi:10.1093/icvts/ivaf031
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。