文献速递瓣膜外科先天性心脏病外科

基于仿真的主动脉瓣二瓣化设计

Simulation-based design of bicuspidization of the aortic valve.
PubMed 文献 · J Thorac Cardiovasc Surg · 2024-01-10

本研究通过流体-结构相互作用仿真,在单一患者特异性几何模型中构建不同游离缘长度和总体形态的模型二瓣化主动脉瓣,评估狭窄与反流。结果显示游离缘长度≥1.5d可避免狭窄,≥1.7d出现明显膨出,1.5d至1.6d时总游离缘长度约等于瓣环周长且表现最佳。

要点

  • 游离缘长度≤1.3d时狭窄明显,≥1.5d时无狭窄发生。
  • 所有模型均无反流。
  • 游离缘长度≥1.7d出现明显膨出及其他总体形态改变。

核心结论

  • 仿真中游离缘长度≥1.5d可避免主动脉瓣狭窄。
  • 游离缘长度≥1.7d的病例出现过度膨出及其他总体形态改变。
  • 游离缘长度1.5d至1.6d的病例总游离缘长度约等于瓣环周长,表现最佳。
  • 这些效应应在体外和动物研究中进一步研究。

研究设计与样本

  • 基于仿真的设计研究,构建不同游离缘长度和总体形态的模型二瓣化瓣。
  • 在单一患者特异性模型几何中进行流体-结构相互作用仿真。
  • 评估主要目标为狭窄和反流,次要目标包括定性血流动力学、几何高度、有效高度、瓣口面积和膨出。

主要发现

  • 狭窄随游离缘长度增加而减少,游离缘长度≤1.3倍瓣环直径d时狭窄明显。
  • 游离缘长度≥1.5d时无狭窄发生。
  • 所有模型均无反流。
  • 游离缘长度≥1.7d时出现明显膨出。
  • 游离缘长度1.5d至1.6d时总游离缘长度约等于瓣环周长,表现最佳。

关键数值与推荐

  • 游离缘长度≤1.3d时狭窄明显。
  • 游离缘长度≥1.5d时无狭窄发生。
  • 游离缘长度≥1.7d时出现明显膨出及其他总体形态改变。
  • 游离缘长度1.5d至1.6d时总游离缘长度约等于瓣环周长,表现最佳。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 仿真在单一患者特异性模型几何中进行。
  • 这些效应应在体外和动物研究中进一步研究。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: Severe congenital aortic valve pathology in the growing patient remains a challenging clinical scenario. Bicuspidization of the diseased aortic valve has proven to be a promising repair technique with acceptable durability. However, most understanding of the procedure is empirical and retrospective. This work seeks to design the optimal gross morphology associated with surgical bicuspidization with simulations based on the hypothesis that modifications to the free edge length cause or relieve stenosis. METHODS: Model bicuspid valves were constructed with varying free edge lengths and gross morphology. Fluid-structure interaction simulations were conducted in a single patient-specific model geometry. The models were evaluated for primary targets of stenosis and regurgitation. Secondary targets were assessed and included qualitative hemodynamics, geometric height, effective height, orifice area, and billow. RESULTS: Stenosis decreased with increasing free edge length and was pronounced with free edge length less than or equal to 1.3 times the annular diameter d. With free edge length 1.5d or greater, no stenosis occurred. All models were free of regurgitation. Substantial billow occurred with free edge length 1.7d or greater. CONCLUSIONS: Free edge length 1.5d or greater was required to avoid aortic stenosis in simulations. Cases with free edge length 1.7d or greater showed excessive billow and other changes in gross morphology. Cases with free edge length 1.5d to 1.6d have a total free edge length approximately equal to the annular circumference and appeared optimal. These effects should be studied in vitro and in animal studies.

来源:J Thorac Cardiovasc Surg,查看原文。版权归原作者所有。

引用

  1. Kaiser AD, Haidar MA, Choi PS, et al. Simulation-based design of bicuspidization of the aortic valve. J Thorac Cardiovasc Surg. 2024. PMID: 38211896. doi:10.1016/j.jtcvs.2023.12.027

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。